DIY Yeti Cooler Sliding Feet

This my Yeti Tundra 45 that I’ve done some other videos on. I did one on a DIY divider right here. I’ve been working on something else. When I first got the Yeti I was surprised that they had these rubber feet because I was used to other coolers where you could just easily slide the cooler around and the Yetis just do not slide. Especially if you have a like a rubber bed mat in the back of your

Read more

Aviation | How to Drink

Hi, I’m Greg and this is how to drink. I’ve never worked in a bar, been a bar back, been a bar apprentice been in… I’ve been in bars, I’ve been in a lot of bars. This is how to drink, a show about making cocktails and drinking them. Let’s get going. Let’s make an Aviation. We’re going to need a bottle of gin. I Like Ford’s Gin. We’re gonna need this stuff, this is creme yvette. We’re gonna put

Read more

How to Build a Jumbo Dart Paper Plane

Hey, guys! Welcome to Nighthawk Gliders. I’m Brad. Today I am going to show you how to build the “Jumbo Dart.” This is a two-sheet paper airplane. Not your typical one-sheet and this glider is amazing. You’re really going to like this glider and it requires two sheets of 8 1/2″ x 11″ If you happen to have a stapler, great, otherwise a little bit of tape that will be just fine. What’s great about this glider, being a dart,

Read more

Bavarian RC Nord 2501 Noratlas – Build video

Welcome back to Bavarian RC. Today I’m gonna show you how to build the Bavarian RC Noratlas. If you haven’t seen the release video check the link in the description below. The Nord 2501 Noratlas was a military transport aircraft developed in the late 1940s. It saw operation mainly in the French and German Air Force. Designing the Noratlas was pretty much inspired by a control line Noratlas designed by my Dad back in the late 1950s. In this video

Read more

Glider-Eating Tree (Will I get my CLG back?)

Brad: Once again, caught in a glider eating tree! Brad: Hey guys I’m Brad. This is Nighthawk Gliders. If this your first time here… Thanks, for stopping by! Hey so this weather here in central Indiana has been pretty bad this year as far as winter goes we get snow and then wind and then it rains and it gets all muddy and then it gets cold again it snows and rains really haven’t had a whole lot of time

Read more

Sliding Door Tool Cabinet

New shop space! We recently moved to San Antonio and I’ve been slowly converting the garage into a workshop. It’s in disarray, but everything is here and accounted for! A stack of scrap lumber, let’s make something! Cutting up 2×4’s to frame out the cabinet. Attaching to the studs with some heavy duty screws. Leveling before driving the rest of the screws in. Attaching cross members mostly to act as nailers. Attaching the top of the framing. Ripping some plywood

Read more

Nighthawk Gliders – Eclipse Edition – Part 1

Check it out! We can project an image on this whiteboard using some binoculars. Hey Guys! Here we are at White House, Tennessee. Just north of Nashville… and crowds are gathering for a spectacular event. It’s going to be a Total Solar Eclipse… and we’re here to see this big ball of fire get covered up by the moon. It’s going to be phenomenal! Welcome to Nighthawk Gliders… I hope you enjoy! We’re going to watch a solar eclipse here…

Read more

How to Build a Balsa Glider – 12″ Sandpiper – Part 2

For the fuse, you have to think about sanding in multiple dimensions. Before we sand this, we should mark a couple points on the top of the glider as to where the wings will be and as to where the tail will be. On the very top, we’re going to measure 2 3/4” and draw a line. That will be the leading edge of the wing. And then 2” from there, since that is the chord, we’ll draw another line.

Read more